Some NAS boxes though are much more than just a network storage solution, they can be a useful and powerful tool for home and business users alike, they can have features like being a mail server or even a multi-media server, and some offer the ability to hook up a camera and be a surveillance system for your home or business. Kernel command line: console=ttyS0,115200 ubi.Network Attached Storage or NAS boxes are something that has become very popular over the last couple years, the main reason being of course that we’ve got more stuff, and we want to share it. Built 1 zonelists in Zone order, mobility grouping on. Memory policy: ECC disabled, Data cache writeback Machine: Marvell SheevaPlug Reference Board CPU: VIVT data cache, VIVT instruction cache Image Type: ARM Linux Kernel Image (uncompressed) # Booting kernel from Legacy Image at 00800000. Marvell> setenv bootcmd 'run bootcmd_usb usb stop run rescue_bootcmd reset' Marvell> setenv rescue_bootcmd 'if test $rescue_installed -eq 1 then run rescue_set_bootargs nand read.e 0x800000 0x100000 0x400000 bootm 0x800000 else run pogo_bootcmd fi' Marvell> setenv rescue_set_bootargs 'setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params' Marvell> setenv ethaddr 00:10:75:XX:XX:XX On Terminal #3 stop the boot process and issue following commands: +1 Extra steps to write rescue image to NANDĭownload rescue images and put them to a local TFTP server: NAND write: device 0 offset 0x0, size 0x80000 *** Warning - bad CRC or NAND, using default environmentġ2. Switch to Termnal #3 and press a key to stop boot process: On Terminal #2 issue following connmmand and be prepared co switch to Termianl #3 within 3 seconds and press a key to stop boot process.ġ1. #Seagate dockstar keeps disconnecting serial#Open Terminal #3 and connect it to Dockstar's serial port via USB2Serial adapterġ0. #0: NAND 256MiB 3.3V 8-bit (Micron) pagesize: 2048, buswidth: 8,Ĭhecked NAND flash device for bad blocks, use "nand info" command to list blocksĩ. NAND flash device 'NAND 256MiB 3.3V 8-bit (Micron)' found Halt command lead my Dockstar to "target halted in Thumb state", which wasn't enough to access the NAND. With "soft_reset_halt" no need to be lucky with reset button. There are a few guides which operates with halt command and immediate press reset button. Update: The trick was to issue "soft_reset_halt" instead of "halt". Target halted in ARM state due to debug-request, current mode: Supervisor Requesting target halt and executing a soft reset Telnet: connect to address ::1: Connection refusedĬonnection closed by foreign ~]# telnet localhost 4444ħ. You can minimize this terminal because you do not need to watch thisĦ. Info : feroceon.cpu: hardware has 1 breakpoint/watchpoint unit Info : JTAG tap: feroceon.cpu tap/device found: 0x20a023d3 (mfg: 0x1e9, part: 0x0a02, ver: 0x2) Info : adapter-specific clock speed value 500 Info : Want to set speed to 500kHz, but not implemented yetĮrror: Translation from jtag_speed to khz not implemented Warn : use 'feroceon.cpu' as target identifier, not '0' Srst_only separate srst_gates_jtag srst_open_drain Trst_and_srst separate srst_gates_jtag trst_push_pull srst_open_drain Info : only one transport option autoselect 'jtag' #Seagate dockstar keeps disconnecting driver#Warn : Adapter driver 'buspirate' did not declare which transports it allows assuming legacy JTAG-only Connect Buspirate'c USB port to your USB port and start openocd on Terminal #1: #Seagate dockstar keeps disconnecting download#Download docstar.cfg and change the start of the config fromĥ.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |